LP100 STD Strobe Light
LP100 STD Strobe Light with 10 high performance LEDs and transparent dome
LP100STD call signal strobe light with 10 high performance LEDs and transparent dome. This light has a slightly lower profile compared to the LP100.
Standard 3 pin XLR connectors (female and male) for looping in to the intercom line. This light is of special interest to users preferring a maximum signal visibility.
Size of the base 12,4 x 9 x 4,4 cm (l x w x h).
Dome height 3,5 cm.
Net weight 363 g.
All axxent signal lights have in common:
• Compatible to axxent partyline intercom systems, however, they also work flawlessly with most of the other commonly available partyline systems.
• They use a voltage of approx. 30 volt DC, derived from the XLR connectors. Voltage may drop to 24 volt DC without causing a problem.
Pin layout of the 3 pin XLR connectors:
Pin 2 = plus 30 volts, Pin 1 = minus 30 volts pin 3 serves as loop through of the intercom signal
CP100 Speaker/Main Station
CP100 Speaker/Main Station for one channel
The COM-PAC speaker station CP 100 provides all necessary and important intercom functions and connectors in a compact housing of just 1 U hight. The speaker can be switched off, to allow operation as a main station
The unit may be freely positioned or it can be rack- or wall mounted with optional mounting hardware. When using the CP 100 as a speaker station, power will be supplied by a master station, either MS 100 or MS 200.
When used as a small station an optional external power supply may be used. Here are the two options:
1. With the RS1 power supply, up to four belt packs can be operated with the CP 100 (rear RJ11 receptacle).
2. Power supply axxent PS 100, connecting directly into the intercom cables. The PS 100 powers up to six stations.
MS 100 1 Channel Master Station
front view
rear view
MS 100 1 Channel Master Station Intercom main station for one channel
Features
• 4 pin XLR connector for a headset
• Volume control for headset
• Side tone control
• Three position talk switch for PTT, permanent on, off
• CALL: buzzer alarm on/out
• Push button for call signal light
• MIC/LINE input via 3 pin xlr connector
• Input volume control
• Line output
• Line input
• Outputs for portable other intercom devices
Specifications
Frequency response | 20 Hz to 20 kHz |
Signal to noise ration | ≥85 dB |
Connectors | 3 and 4 pin xlr |
Power supply | 230/110 vac, switchable |
Power consumption | max. 50 watts |
Case | steel, black powder coated |
Dimensions | 482 x 44 x 155 mm (WxHxD) |
Weight | 3,2 kg (net) |
MS 200 2 Channel Master Station
front view
rear view
MS 200 2 Channel Master Station Intercom main station für two full duplex channels
Features
• 4 pin XLR connector for a headset
• Volume control for headset
• Side tone control
• Three position talk switch for PTT, permanent on, off
• MIC switch, via channel A or B, or both channels
• CALL: buzzer alarm on/out
• Push button for call signal light, separately for channels A/B
• MIC/LINE input via 3 pin xlr connector
• Input volume control
• Line output with channel switch (for recording or other purpose)
• Line input with channel selector
• Outputs for portable other intercom devices
Specifications
Frequency response | 20 Hz to 20 kHz |
Signal to noise ration | ≥85 dB |
Crosstalk between channels | ≥65 dB |
Connectors | 3 and 4 pin xlr |
Power supply | 230/110 vac, switchable |
Power consumption | max. 50 watts |
Case | steel, black powder coated |
Dimensions | 482 x 44 x 200 mm (WxHxD) |
Weight | 3,1 kg (net) |
CP-100S Main Station
front view
rear view
CP-100S Main Station with two wire principle for full duplex operation with headsets
The new half 19 inch main station CP100S uses the two wire principle or party line principle for full duplex operation with headsets and has a built in monitoring loudspeaker.
All headsets with dynamic microphone cartridges may be used with the station. Gooseneck microphones or wired microphones may be plugged into the 3 pin xlr connector on the units’ front.
A line termination switch on the back facilitates a stable intercom level. To be switched on when CP100S is being used as a master station. When powered from another station, the switch should not be activated.
The external power supply allows universal operation (100 – 240 V) of approximately 10 components such as belt packs or signal lights.
The CP100S may be mounted in a 19” rack via an optional rack kit RMK100.
Specifications
External power supply | 24 VDC, 1 A secondary, 100-240 VAC primary provides sufficient power for approximately 10 intercom components |
Dimensions | 20 x 12 x 4.4 cm (W x D x H) |
Weight | 785 g net without power supply |
SHOUTBOX
front view
rear view
SHOUTBOX
Intercom main station
COMBOX. is a unique intercom main station combined with a high performance powered loudspeaker. It allows very loud and intelligible voice reproduction as well as program material combined with all intercom station functions.
It may be used with any conventional dynamic headset or dynamic microphone. Its sound pressure level is high enough (up to 115 dB peak) to be heard in noisy stage environments.
COMBOX. is also ideal for use in artists wardrobes or backstage and enables personnel or artists to be heard on the intercom. If you use several COMBOX.es together, you use one as a master and all the others as slave stations. If you use the COMBOX. together with other intercom master stations, you will have to switch the COMBOX. to slave position.
Features
• FeaturesSelf-powered speaker for up to 115 dB SPL.
• Frequency response shaped for high intelligibility.
• Loudspeaker may be muted.
• Partyline intercom functions with all typical features.
• CALL light with ultra-bright LED and yellow CALL PTT button; Piezo buzzer – LED and buzzer switchable.
• Use of headset possible, front connection.
• Instead of headset, dynamic microphone may be used.
• All connection between stations via standard xlr micro-phone cables.
• As a main station, the COMBOX. provides several other intercom components, such as belt packs, call lights etc. with the necessary power.
• Balanced program input for monitoring purposes or to be fed into the intercom signal.
• Wedge design with two angles, table top use or on the floor, 3/8” thread for microphone stands.
• Wooden side bars may be taken off and be replaced by 19” rack mount.
• Universal power supply for use between 100 to 250 VAC.
Specifications
Frequency response | Microphone: 160-20,000 Hz/-6 dB, shaped for intelligibility Loudspeaker: 220-15,000 Hz +/-6 dBMaximum |
Maximum Sound Pressure Level: | 115 dB when speaking loud into a connected intercom beltpack headset |
THD | <0.1%; S/N: >80 dB |
Power Amplification | 20 W |
Signal light | LED white, 80 lm |
Connectors | Front: headset connector 4 pin xlr for headsets with dynamic microphone cartridge Rear: balanced program input, line level, 3 pin xlr Intercom Connection: partyline standard 3 pin xlr parallel in and out Microphone connection: bal. 3 pin xlr with gain control |
Side-Tone | recessed potentiometer on rear side |
Power connection | IEC power connector |
Fuse | 1.6 A slow blow, 5×20 mm |
Power Switch | Robust rocker switch |
Power Supply | internal – 100 V through 240 VAC, 50/60 Hz, 31 watts |
Stand mount | 3/8” thread for microphone stands |
Dimensions | 280 x 170 x 140 mm |
Net weight | 3.65 kg without AC power cable |
RMK100 19″ Rack Mount Kit
RMK100 19″ Rack Mount Kit for CP-100S
WMK100 Wall Mount Kit
.
WMK100 Wall Mount Kit for Speaker/Main Station CP-100S
GN-M100 Paging Microphone
GN-M100 Paging Microphone for Intercom Master Stations
The GN-M100 allows you to page messages through the intercom master stations MS-200 and CP100S. Both master stations feature a 3 pin xlr microphone input. The CP-100S input is for dynamic microphones and the MS200 input adjustable from microphone level to auxiliary level.
The paging microphone has a dynamic microphone cartridge without the need of phantom voltage feed. A 5 meter long connection cable allows remote.
An efficient pop filter with strong wire mesh, together with a rugged gooseneck, guarantees trouble free use of the paging microphone.
Function switch has three positions: Push to talk, latching, off.
Technical Specifications
Response Characteristic | Cardioid |
Frequency Response | 60 Hz to 12 kHz |
Sensitivity | 3.2 mV/Pa at 1 kHz |
Impedance | 600 Ohms |
Gooseneck length | 310 mm |
Net weight | 1.1 kgs |
Intercom Line Splitter ILS3
front view
rear view
Wherever a star topology distribution of a partyline intercom signal is required, the splitter ILS3 is a good solution. It distributes 1 input signal to a maximum of 3. In most cases, a partyline intercom signal is daisy chained from belt pack to belt pack or to other components such as alarm signal lights. However, there are cases where this is not very practical – the ILS3 splitter then comes into place.