LP100 Call Signal Light

LP 100 Signal Leuchte

With 30 volt bulbs and matt dome. 3 pin XLR in- and out connectors for standard microphone cables, looping in to the intercom line. Stable surface placement with rubber feet.

Size of the base 12,2 x 9 x 5,4 cm (l x w x h).
Dome height 4 cm.
Net weight 446 g.

All axxent signal lights have in common:
• Compatible to axxent partyline intercom systems, however, they also work flawlessly with most of the other commonly available partyline systems.
• They use a voltage of approx. 30 volt DC, derived from the XLR connectors. Voltage may drop to 24 volt DC without causing a problem.

Pin layout of the 3 pin XLR connectors:
Pin 2 = plus 30 volts, Pin 1 = minus, pin 3 serves as loop through of the intercom signal.

LP100 LED Call Signal Light

 

LP 100 LED Signal Leuchte

LED signal light with 4 high performance LEDs in red colour with continuously variable brightness (just with the help of a little screw driver). This model is low profile in height due to use of flatly shaped LED covers. Like the other lights, the LP100LED is equipped with 2 standard 3 pin XLR connectors (female and male) for looping in to the intercom line.

Dimension of the base: 12,2 x 9 x 4,4 cm (l x w x h).
The LED dome height merely is 5 mm, the net weight of the unit equals 363 g.

The models LP100LED green, LP100LED yellow, LP100LED orange and LP100red only differ in the colour of the LEDs.

All axxent signal lights have in common:
• Compatible to axxent partyline intercom systems, however, they also work flawlessly with most of the other commonly available partyline systems.
• They use a voltage of approx. 30 volt DC, derived from the XLR connectors. Voltage may drop to 24 volt DC without causing a problem.

Pin layout of the 3 pin XLR connectors:
Pin 2 = plus 30 volts, Pin 1 = minus 30 volts pin 3 serves as loop through of the intercom signal.

 

 

WT100 walkie-talkie interface

WT100 walkie-talkie interface front view

WT100 walkie-talkie interface rear view

to connect the axxent intercom line with two-way radio devices

The interface model WT100 is used to connect the axxent intercom line with two-way radio devices (walkie-talkies). The WT100 is suitable for all such wireless models equipped with connectors for an external microphone and headset. Herewith a communication is established between the stationary intercom system at the venue and the personnel with walkie-talkies on location.

The WT100 derives its voltage supply from the axxent intercom system. The send and receive levels are adjustable separately. A red overload-LED indicates excessive receive signal and helps to set the correct level. The walkie-talkie is attached via a standard DB-9 connector and can accommodate virtually any type of radio. The integration of the interface WT100 with the axxent party-line intercom system is via standard XLR connectors (male/female).

A rugged steel case and high quality components and connectors ensure a long trouble free performance and durability.

Technical Note
The WT100 derives its voltage supply from the axxent intercom system. Send- and receive signals are indicated by colour LEDs. The individual levels may be adjusted separately with the trim potentiometers “Level”. The red LED “Ovl” indicated excessive receive level and thereby facilitates the level adjustment. The type of the connected microphone cartridge is brought in line by the right hand three position switch (“Dyn” = dynamic, “Carb” = Carbon and “Elect” = Electret condenser). Connecting with the radio device is via a standard DB-9 connector on the rear of the unit.
Hint: Optional adapter cables WT100AC for connection of the wireless devices are normally supplied open ended since the connectors vary to a high degree.

Specifications

microphone emulation electret/carbon, dynamic (selectable via switch on front)
microphone level carbon +10 dBu, electret -20 dBu, dynamic -36 dBu additionally adjustable via potentiometer “Send Level”
monitor level (head-/earphone) adjustable via potentiometer “Receive Level”
talk button
supply voltage 20 – 30 V (derived from axxent intercom system)
current consumption idle <30 mA, transmitting 60 mA
connectors XLR male/female, DB-9F
adaptor cable to radio device WT100AC optional. DB9 connector, 1,5 m cable, open wire ends complete device related connection solutions upon request
dimensions 88 x 44 x 123 mm (w x h x d)

Technical data subject to change without notice

PS100 Power Supply

PS 100 Netzteil front view

PS 100 Netzteil rear view

for of up to 6 belt packs

This power supply allows the operation of belt packs BP 100BP 100 Vsignal lights LP 100 and LP 100 LED and the CP 100s loudspeaker station – all without the necessity of 19″ main stations.

Since more digital mixing consoles are used, less side racks are used and therefore this type of a power supply is an ideal compact solution. Up to 6 intercom belt packs are powered by the PS100. The unit features two party line intercom outputs with XLR male connectors, an interchangeable fuse and a voltage selector switch 120/230 VAC.

 

BP100 Belt Pack

MS 200 2-Kanal-Hauptstation Front View

MS 200 2-Kanal-Hauptstation Rear view

portable one channel intercom station

The belt pack BP 100 is a portable 1 channel intercom station for connection to a main station MS 200. The integrated spring steel clip allows for easy fixing the unit to clothes. All controls on the front side of the unit are identical to those on the main station.

On the rear of the unit all XLR connectors are easily accessible (left on photo the 4 pin XLR connector for the headset and on the right the 3 pin XLRs for signal loop-through to the next station). The side tone is adjustable. Nearly all features are identical to those on the main station. The BP 100 features light and sound alarm. The sound alarm is switchable.

 

BP100 V Belt Pack Vibration

MS 200 2-Kanal-Hauptstation front view

portable one channel intercom station

The belt pack BP 100 V is a portable 1 channel intercom station for connection to a main station MS 200. The integrated spring steel clip allows for easy fixing the unit to clothes. All controls on the front side of the unit are identical to those on the main station. On the rear of the unit all XLR connectors are easily accessible (left on photo the 4 pin XLR connector for the headset and on the right the 3 pin XLRs for signal loop-through to the next station).

The side tone is adjustable. Nearly all features are identical to those on the main station.

The BP 100 V features light alarm and a connection for an external vibration alarm module (only 5 x 4 x 2 cm). The connection cable has a length of 80 cm and is equipped with a mini phone plug. The “Vibro Alarm” comes in handy, when the light alarm is not recognized by any reason. The BP 100V is compatible to other common Partyline intercom systems.

VP 100 Vibration Alarm Module

RS-1 Netzteil

Vibration Alarm Module

The axxent Vibration Alarm Module VP100 is a small ABS plastic box with a vibration element inside. The box measures 50 mm to 40 mm to 20 mm and is very light weight. Its connection cable is 80 cm long and it plugs into the belt packs BP101 or BP100V via a 3.5 mm phone plug.

 

BP101 Belt Pack

MS 200 2-Kanal-Hauptstation Front view

MS 200 2-Kanal-Hauptstation Rear View

portable single channel intercom station

The belt pack BP-101 is a portable single channel intercom station. It is compatible to common Party Line Intercom Systems.

All controls on the front side of the unit are identical to those on the main stations. Knob on right side is headset volume. The side tone is adjustable via slotted screwdriver. The talk switch has three positions: Middle is Off, Top is momentary “Push to Talk”, Down is Talk (On). The BP-101 features light and sound alarm. Illuminated yellow pushbutton has the CALL function. The sound alarm is switchable.

BP-101 features a connection (3.5 mm socket on left side of front panel) for external “vibration alarm module”. When the plug of an external “vibro alarm module” is inserted, the internal buzzer is automatically disabled.

The “CALL Signalling” has two modes of indication (selectable via recessed switch on left side of front panel):

Extended Mode (Lever Down): CALL Signal is pulsing and extended, ~ 4 seconds.

Instant Mode (Lever Up): Indication follows the CALL Signal on the Line. Then duration of the CALL Signal means the ATTENTION. End of CALL Signal means the Start of the Action.

Three XLR connectors are easy accessible on the rear side of the BP-101 (the 4-pin XLR connector for the headset and 3-pin XLRs for Party Line). The integrated spring steel clip allows for easy fixing the unit to trouser belts.

Technical Specifications

Frequency Response Mic: 160 Hz to 20 kHz/ – 6 dB, shaped for better intelligibility Rep: 220 Hz to 15 kHz/ ± 6 dB
THD + N <0,1 %
Signal to Noise Ratio >80 dB
Connectors 3 and 4 pin XLR, 3,5 mm socket
Power Requirements 20 – 30 VDC
Current Consumption < 30 mA, idle <100 mA, in use
Dimensions W = 80 mm, L = 125 mm, H = 40 mm
Weight 324 gramms

 

 

D800 Dual Headset

D 800 Pro Headset

Microphone/Headphone Combinations 

These four headset models have been especially designed for intercom applications. Selection of the right model pretty much depends on the application project and the system specifications.

The headsets are made of rugged PE plastic material. All models have been developed with the correct acoustical and electrical insulation between microphone and head phone in mind. Hereby the usual crosstalk problems normally associated with multi channel intercom systems could be minimized. Special ear cushions provide the acoustical insulation without degrading the comfort, even at longer sessions and high environmental noise levels.

The balanced microphone provides a precise cardioid pattern and a highly effective windscreen.

Features
• extremely robust
• optimized for high intelligibility
• high sound pressure capability
• budget price

Specifications

Headphone
frequency response 40 to 14.4Hz
impedance 400 Ω system
sound pressure level ≥94.dB
power handling 100 mW
suppression of environmental noise ca. 16 dBA
weight (w/o cable) 270 g
cable length 1.5 m
ear cushion “circumaural” skin friendly antiseptic surface
Microphon
frequency response 40 to 15 Hz
directional pattern cardioid
impedance 100 Ω (200 Ω) bal.
output voltage at 5 cm distance ≈3 mV/Pa
pivot angle

 

 

D900 Dual DeLuxe Headset

D 900 Pro Headset

Microphone/Headphone Combinations 

These four headset models have been especially designed for intercom applications. Selection of the right model pretty much depends on the application project and the system specifications.

The headsets are made of rugged PE plastic material. All models have been developed with the correct acoustical and electrical insulation between microphone and head phone in mind. Hereby the usual crosstalk problems normally associated with multi channel intercom systems could be minimized. Special ear cushions provide the acoustical insulation without degrading the comfort, even at longer sessions and high environmental noise levels.

The balanced microphone provides a precise cardioid pattern and a highly effective windscreen.

Features
• studio sound quality
• easy to wear, even for long sessions
• microphone arm left or right
• microphone is automatically off in the upper position (micro switch)

Specifications

Headphone
frequency response 10 to 34Hz
impedance 400 Ω system
sound pressure level ≥94.dB
power handling 100 mW
suppression of environmental noise ca. 25 dBA
weight (w/o cable) 350 g
cable length 1.8 m
ear cushion “circumaural” skin friendly antiseptic surface
Microphon
frequency response 40 to 15 Hz
directional pattern cardioid
impedance 100 Ω (200 Ω) bal.
output voltage at 5 cm distance ≈1 mV/Pa(≈3 m V/Pa)
pivot angle 300°
connectors 4 pin XLR-Female

 

Marcas